Search results

A safe and ecological solution for most surfaces. CONTENT What are the best methods for removing these impurities? How to clean the hob without scratching? What cleaning products are most effective and safest for these surfaces? How often should these surfaces be cleaned to maintain their best appearance and functionality? Are there any homemade cleaning products that are as effective as commercial products? Introduction   Maintaining cleanliness in the home is key to maintaining not only the aesthetic appearance, but also hygiene. However, some surfaces, such as the glass in the oven or the hob, can be particularly difficult to clean. Dried grease, burns and other debris can make your kitchen appliances look neglected and can even affect their performance. In this article, we will introduce you to effective and gentle methods to effectively clean the glass in the oven and the hob so that you can make your kitchen shine again.    What are the best methods for removing dirt from oven glass? The glass in the oven can get dirty very quickly due to frequent baking, especially if you let the dirt settle. Dried fat and baked-on residues can not only look unsightly, but can also cause an unpleasant smell during further baking. Fortunately, there are several proven methods to help restore the cleanliness and shine of your oven.   1. The baking soda and vinegar method   Method: Mix baking soda with a little water to make a paste. Apply it on the glass of the oven and leave it for 15-20 minutes. Then spray the paste with vinegar, which will create a foaming reaction that loosens the dirt. Finally, wipe with a damp cloth.   Advantages: This method is environmentally friendly and effective on stubborn stains. Cons: The process may take a little more time than using commercial cleaners.   2. A paste of baking soda and water   Procedure: If you prefer simple and natural solutions, mix baking soda with water until a thick paste is formed. Apply it to the glass, leave it on for 20 minutes and then wipe it off with a damp cloth.   Advantages: Friendly to the environment, safe for surfaces. Cons: May be less effective on very heavily baked-on stains.    3. Use of commercial cleaning agents   There are a number of cleaning products on the market designed specifically for the oven. Procedure: Apply the glass cleaner according to the manufacturer's instructions, then wipe with a clean cloth.   Advantages: Quick and easy to use with an immediate effect. Cons: Some products may contain harsh chemicals that should be used with care.     These methods will help you achieve sparkling clean oven glass that looks like new.      How to clean the hob without scratching?   The hob is one of the most used surfaces in the kitchen and at the same time one of the most susceptible to damage. To prevent scratches and preserve its shine, it is important to use the correct cleaning techniques and products.     1. Using a soft cloth or sponge   Procedure: Use a soft cloth or sponge for daily cleaning. Avoid abrasive sponges or wire brushes that can scratch the surface. Just apply a little mild detergent to the sponge and gently wipe the hob.   Advantages: Economical and safe for most types of hobs. Cons: Requires regular cleaning to prevent dirt build-up.   2. Special cleaning agents for glass ceramics   Procedure: Use special cleaning agents designed specifically for glass-ceramic hobs. These products are formulated to be effective in removing burns without damaging the surface. Apply a small amount to the hob and wipe with a soft cloth.   Benefits: Safe for sensitive surfaces, effective on stubborn stains. Cons: Some products can be more expensive than regular cleaners.   3. Removing stubborn stains   Procedure: If stubborn stains appear on the hob, you can use a paste of baking soda and water. Apply the paste to the stain, let it sit for a few minutes, then gently wipe with a damp cloth. For very stubborn stains, you can use a plastic scraper designed for glass-ceramic plates.   Benefits: Effective on burns and grease. Cons: Care must be taken when using the scraper to avoid scratching.   With these simple steps, you can keep your hob in perfect condition and extend its life.      What cleaning products are most effective and safest for these surfaces?   Choosing the right cleaning agent is key to achieving optimal results when cleaning, whether it's the glass in the oven or the hob. It is important to use products that are not only effective, but also gentle on surfaces and safe for your health.     1. Baking soda and vinegar Suitable for: Ovens, glass surfaces, hobs.   Advantages: This combination is ecological, non-toxic and very effective in removing grease and burns. In addition, it is gentle on surfaces and does not leave a chemical smell.   Use: Baking soda acts as a mild abrasive, while vinegar dissolves grease and neutralizes odors.   2. Cif cream Suitable for: Ovens, ceramic and glass ceramic hobs.   Benefits: This commercial product is popular for its ability to quickly remove stubborn stains and grease without damaging the surface. It is suitable for daily cleaning as well as for deep cleaning.   How to use: Apply a small amount of cream to a sponge and gently spread over the surface, then wipe with a damp cloth.   3. Cerapol – cleaning agent for glass ceramics Suitable for: Glass ceramic hobs.   Advantages: Cerapol is specially designed for cleaning glass-ceramic surfaces. Effectively removes burns and grease without leaving scratches. It is safe and simple to use.   Use: Apply to a cold hob, spread gently and wipe with a soft cloth.   4. Home remedies – lemon juice and water Suitable for: Less dirty surfaces, refreshing and removing odors.   Benefits: Lemon juice is naturally acidic, making it a great grease remover and natural deodorant. It's a simple and inexpensive solution that will also leave your kitchen smelling fresh.   Use: Mix lemon juice with water in a 1:1 ratio, apply to the surface and wipe with a clean cloth.   5. Clin - glass cleaner Suitable for: Ovens, glass surfaces.   Benefits: Clin is an effective glass cleaner that easily removes grease and smudges. Leaves the glass sparkling clean and smudge-free.   Application: Spray directly on the glass and wipe with a dry cloth or paper towel.   Using these proven cleaning products will give you great results and keep your kitchen looking like new. Remember that proper care of these surfaces can not only improve their appearance, but also extend their life.   How often should these surfaces be cleaned to maintain their best appearance and functionality?   Regular maintenance and cleaning of kitchen appliances and surfaces is essential for their long life and maintaining a perfect appearance. However, each surface requires a different frequency of cleaning, depending on how often and intensively you use it.   1. Hob   After each use: After each cooking, it is a good idea to wipe the hob with a soft cloth moistened in warm water with a little detergent. This will help remove fresh dirt and prevent it from settling.   Once a week: Carry out a more thorough cleaning using a special cleaning agent for glass-ceramic surfaces to remove possible burns and keep the hob in perfect condition.   2. Glass in the oven   Once a month: For basic maintenance, it is advisable to clean the oven glass at least once a month, especially if you bake often. Use the baking soda and vinegar method or commercial cleaners.   After large culinary events: If you prepare a large baking event, for example during the holidays, it is a good idea to clean the glass immediately after finishing, before the dirt settles and dries.   3. Oven - general maintenance   Once every 3 months: For a thorough cleaning of the oven, which includes not only the glass, but also the inner walls and grates, it is advisable to carry out this maintenance at least four times a year. This ensures that the oven is hygienic and ready for any culinary task.   Regular maintenance not only ensures cleanliness, but also contributes to the safer and more efficient operation of your appliances. If you follow these steps, your cooktop and oven will serve you well for many years.    Are there any homemade cleaning products that are just as effective as commercial products?   In many cases, you can achieve excellent results when cleaning kitchen appliances even by using home remedies, which are often cheaper and more environmentally friendly than commercial products. Here are some of the most effective options:   1. Baking soda and vinegar   Uses: Baking soda is excellent for removing grease and burns due to its mild abrasive nature. Vinegar neutralizes odors and dissolves fats. Mixing these two ingredients creates a foamy mixture that is great for cleaning the oven, hob and other kitchen surfaces. Advantages: Non-toxic, safe for food surfaces, environmentally friendly. Cons: Can be more time consuming than using commercial products when cleaning larger areas.   2. Lemon juice   Uses: Lemon juice is naturally acidic, which makes it a great agent for removing grease and dirt. It is also an excellent deodorant and leaves a fresh scent. It can be used on hobs, glass surfaces and kitchen appliances.   Pros: Natural, cheap, leaves a fresh scent. Cons: Lemon juice is not suitable for all surfaces, especially those that are sensitive to acids such as marble.   3. Baking soda and water   Use: For gentler cleaning, you can mix baking soda with water to create a paste that can be used on the stovetop, oven glass, and other surfaces. This paste gently removes dirt without damaging the surface.   Advantages: Safe and gentle for everyday use. Cons: May be less effective on very stubborn stains.   4. A mixture of soap and warm water   Use: For quick daily cleaning, a mixture of warm water and mild soap is a great choice. This mixture is gentle on surfaces and effectively removes common dirt.   Advantages: Easily accessible, suitable for daily maintenance. Cons: Not suitable for deep cleaning and stubborn stains.   Using home remedies is a great alternative if you are looking for ecological and gentle solutions for cleaning your kitchen. Although they may not always be as strong as commercial products, their regular use can go a long way in keeping your home clean and fresh.     Conclusion   Proper cleaning of kitchen appliances and surfaces such as the oven and hob is essential to maintain their functionality and appearance. By using the right techniques and remedies - whether commercial or homemade - you can ensure that your kitchen is always sparkling clean. However, if you are looking for professional cleaning services that will take care of everything for you, do not hesitate to contact us. We are happy to help you!   If you know of another method, how to clean the glass in the oven and the hob , share with us this experience of yours or acquired experience...

or So that the windows are not only pretty It's not enough for the windows to be pretty - the windows have to work too! In order for the windows to seal properly, not to creak, not to stick, not to get stuck, or so that unpleasant melusin does not settle in them over time, it is necessary at least once a year basic window maintenance . CONTENT Seal treatment and replacement Hardware maintenance Checking the drainage system Seal treatment and replacement In order to eliminate the risk of heat loss in the winter months and to prevent unpleasant blowing of the window in autumn, it is necessary to rub their seals with the appropriate oil (silicone, glycerin) at least once a year (preferably before the onset of winter), which will ensure flexibility and a longer service life. Mineral oils, table oils, etc. are completely unsuitable. If the gasket shows signs of wear (or does not return to its original shape when felt), replace it with a new one. Uncompromisingly. In this case, there is no small or large wear - the problem arises in just a millimeter of leakage... It is better to entrust the replacement of the seals to a professional company, but if you are manually skilled and trust yourself… Pull out the old or damaged gasket from the groove and push the new one back into it. Buy the gasket where you bought the windows, because every window has a different frame profile, a different wide groove. Notice Avoid gaskets when cleaning frames – cleaning agents reduce their elasticity and shorten their lifespan! Soapy water is enough to clean it. Hardware maintenance All windows (except fixed ones) have so-called fittings that allow manipulation (opening - closing) and ensure safety (locking). Maintenance of this fitting means lubricating all functional (moving) parts with oil, preferably silicone-based (WD-40, sewing machine oil), or special oil directly from the window manufacturer - definitely do not use table oil or oils containing acids or resins. First, clean all metal parts with a damp cloth (in case of heavy contamination, use denatured alcohol). Then apply oil to hinge pins, tie rods and locking points. A few drops into the lubrication holes (see picture) will suffice. Lubrication plan for the metal parts of the window On this occasion, check and, if necessary, tighten the screws of the individual parts of the fittings , as well as the handles, which loosen over time (you can usually reveal these screws by moving the plastic cover under the handle). Notice When cleaning the frame, make sure that the cleaning agent does not get on the fittings, as this would damage its corrosion protection. Checking the drainage system The windows are designed with drainage systems that prevent water from accumulating in the structure - or serves for the escape of rainwater, which from time to time gets between the frame and the window sash. When water does not drain properly to the exterior, it can flow into the interior and cause damage. Therefore, it is more than advisable to check the condition of these drains every time you wash the windows and frames. The drainage channels can be found in the lower part of the frame after opening the window. The drains are accessible after removing the plastic covers on the outside a few centimeters from the windowsill. You can check the functionality simply: pour a small amount of water into the inner frame. If the water drains through the external drain holes or slot, the system is clean. If the water does not flow or flows slowly, poke the channel with a cotton swab, wire, match or toothpick. Repeat until clear water comes out of the hole. Tips Try using sunscreen to remove alcohol marker from plastic window frames . It is non-aggressive and ecological. Lubricate the marker mark with a little cream and wipe with a dry, clean cloth. Wash the wooden surfaces of the window frames with soapy water and once in a while rub them with floor paste (parquet wax) and polish them - this will prevent the accumulation of dust, and by occasionally polishing them, you will make their maintenance easier. Basic window maintenance will extend the life of your windows… Images on this page are sourced from Depositphotos.

Instructions and tips CONTENT Color removal by non-toxic method Chemical removal of paint Color removal by non-toxic method Turpentine Suitable for removing oil paint (alkyd-based) and enamels. Apply to the paint and let it work. Then wipe with a damp cloth. White vinegar, distilled Suitable for textured glass where scratching is not possible. Mix three tablespoons of hot water with the same amount of vinegar you previously heated in the microwave (thick rubber gloves are a must). Scrub off the paint with this solution, then wash the glass in the standard way. Source Scraper and cleaner A razor blade can be used instead of a scraper. Mix warm water with a little dishwashing liquid to create a rich lather that will make it easier to move the scraper over the surface of the glass, minimizing the risk of scratching it. Source Baby shampoo Only effective on fresh paint. Using a kitchen sponge, scrub the paint with a solution of shampoo and water. Do not use the sponge with the rough side, you will scratch the glass! Sodium hydroxide, slaked lime, crushed chalk Removes most types of paint. Mix the lime with the chalk until it has a smooth texture, then add the soda. The resulting porridge should have the appearance of thick sour cream. Apply it to the paint and leave it on for a few hours. Separate the paint from the glass with a scraper. Mayonnaise Also suitable for stained tiles, switches, paneling or door handles. As with the glue, the oil and vinegar in the mayonnaise also help break down the paint. Not suitable for porous substrates (may leave a stain). Put 4 tablespoons of mayonnaise and 1 tablespoon of wine vinegar in a bowl. Mix the ingredients well and apply the resulting paste in a thin layer to the paint. Leave the mixture on for about 20 minutes. Use anything plastic or a wet cloth to remove. Finally, rinse the glass with soapy water. Toothpaste and baking soda Toothpaste contains glycerin, which is a good mixing agent. Mix equal parts toothpaste and baking soda. Apply this mixture on the stain and leave it on for a while. Then wipe off the drop of paint with a damp cloth and circular movements. Hot air stream This method is suitable for removing strongly dried stains of many types of paint, which the hot air stream softens and thus weakens their adhesive properties. Heat the stain with a hair dryer until it softens and loosens, then scrape the color off with a putty knife, plastic knife, razor blade, or scraper. Clean the paint stain with a cleaning agent or a drop of white spirit. By using a small amount of vinegar and water (1:5) when cleaning, you will achieve a high shine. Be careful when heating the paint on the glass - the glass must not be overheated, as this could cause microcracks or cracks! How to remove paint drips from windows, if the aggressive method has failed? Aggressive chemistry! Chemical removal of paint Probably the best (easiest) option is to purchase a specialized product , the so-called old paint remover, which is based on organic solvents that allow you to remove old one-component and two-component coatings from metal, wood, glass, stone, concrete, etc. surfaces. However, it is very likely that you already have some solvent (cleaner) in your home or garage. Acetone, alcohol, gasoline, methanol, toluene, turpentine, esters, dichloromethane, ketones, hexane are used as solvents (and therefore cleaners). The most used solvents are: Technical alcohol (ethanol) 95% denatured Technical gasoline Technical acetone Isopropyl alcohol (IPA) Use acetone solvents (thinners) for enamel paints . Use alcohol-based cleaners for acrylic paints . Thinners: C6000 – nitrocellulose, acrylic and polymerase paints S6005 – synthetic paints S6006 – oil and synthetic paints U6003 – polyurethane paints Cellulose thinners will remove most types of paint. Chemistry alone is sufficient to remove small drops of paint, for larger (old, dried) stains it is also necessary to use mechanical tools, such as a razor blade or scraper. Method of use Drop the paint with the solvent (thinner, cleaner) and let it work until the paint starts to swell (softens). Dip a cloth in the same liquid and rub the paint back and forth until it loosens. The higher the concentration of the product, the better. If the stain still resists, use a scraper, razor blade, plastic knife or credit card (depending on the type of substrate). Notice Be very careful when working with the above chemistry. Follow the manufacturer's instructions and observe the safety instructions. Ventilate a lot, use gloves and safety glasses. If you feel dizzy, leave the work area immediately and breathe. If the chemical substance gets on your mucous membranes, it is necessary to rinse the affected area with running water as soon as possible and then seek the help of a doctor. Do not use solvents (thinners) on plastics or aluminium . Plastic will be damaged, aluminum will corrode. ...and one semi-aggressive method at the end Mix 250 ml of water, 1 teaspoon of benzine and a few drops of glass cleaner. Clean the affected area with this mixture and rinse. Finally, polish with a micro fiber cloth. Helpful footnote Anyone who does anything knows very well that anything that can go wrong, will - to put it politely - go wrong. Sometimes more, sometimes less. Nothing in this world is perfect. Fortunately, we are always comforted by the real possibility of correction. If you "succeeded" in scratching the window while removing the paint, and the scratches are not too significant (big), here is the repair guide: Apply a small amount of non-gel toothpaste to the affected area and use a microfiber cloth to gently buff the scratch in a circular motion for about 30 seconds. Then wash the entire window in the standard way. The result will amaze you or disappoint you. You know - that's life... If you know other methods, how to remove paint drips from windows , share with us these experiences of yours (or yours). The source of the images on this page is Freepik.

You can usually get rid of labels on glass or plastic by soaking them in hot spring water. But it's quite understandable that you won't want to soak, for example, your beloved stereo... All information about stickers can be found on this server: http://cz.misetiquetas.com/info . How to remove labels and adhesive residues? It is true about adhesive removers that the gentler they are on the substrate, the fewer types of adhesives they can damage. Therefore, if you want to remove the sticker without damaging the substrate, it is advisable to try non-aggressive methods first. When these fail, you can go on a brutal chemical offensive… CONTENT Non-aggressive label removal Chemical removal of labels Removal of labels according to the type of substrate Non-aggressive label removal A stream of hot air This is probably the most effective method, but not every surface can withstand it, so caution and testing is in order. Heat the label with a heat gun or hair dryer until it starts to shrink (swell, wrinkle) and continuously test its resistance with your fingernail (about 30 seconds). When it loosens, remove it with anything made of plastic (spatula, knife, credit card). If the substrate is glass, you can use steel (scraper, razor blade, spatula). Use your thumb to roll up the leftover label and glue. Soda Mix the solution with a low concentration, otherwise you risk scratching the surface of the product. Apply the mixture to the tag, leave for 5 minutes, then remove the tag with a sponge and warm water. Lemon Perfectly corrodes the sticky structure. An alternative is a solution of citric acid and water in a ratio of 1:1. Cut the lemon in two. Wipe the label with one half for a moment and cover the label with the other half for about 5 minutes. Vinegar (white, table) Handles all types of pollution. It is also ideal for removing paint residue from tiles, baseboards, etc. Heat the vinegar in the microwave or on the stove without bringing it to a boil. Immerse the object in warm liquid if size permits. If not, soak a cloth in the liquid and drape it over the item. Allow the white vinegar to soak into the label for 15-30 minutes, then begin to peel off one corner of the label, the rest should follow. Use a damp sponge to scrub the residue off the surface. Source Warning Do not use vinegar on marble, stone, aluminum or cast iron. It could damage their surface and the objects would start to rust. Suds Any soap - household or toilet, liquid or lumpy. Make a strong solution, moisten a cloth in it and place it on the label for several hours. If the label still resists, cover it with plastic overnight - it should loosen in the morning. Natural oils (herbal and essential, tea or eucalyptus extracts) Some natural oils, such as sunflower oil, olive oil or almond oil, are excellent at releasing the adhesion of labels. For use on non-porous surfaces. Apply the oil to a cloth (preferably a micro cloth) and massage it into the label in a circular motion. After about 10 minutes, slowly and carefully scrape off the label. Do not forget to degrease the surface. Source Vegetable oil + baking soda For use on non-porous surfaces. Baking soda can be replaced with ammonia. Mix equal amounts of oil and baking soda. Apply this paste to the label and remove it after a few minutes. Do not forget to degrease the surface. Coconut oil + baking soda It is used if the base of the label is metal. Add water and mix to form a thick paste. Exposure time 30 to 45 minutes. Source Technical lubricant WD-40 A very popular aerosol based lubricant. For use on non-porous surfaces. Spray the sticker with this universal lubricant and let it work for a while. Then wet the cloth with warm water and scrub. And again: don't forget to degrease the surface. Mayonnaise + wine vinegar Oil and vinegar in mayonnaise are really effective helpers in breaking down the glue. This method can be used to remove a label from a glass, a sticker from a car bumper or a price tag from your new lipstick… However, mayonnaise should not be used on porous materials such as wood, plastic and fabric as it may leave greasy stains on them. Put 4 tablespoons of mayonnaise and 1 tablespoon of wine vinegar in a bowl. Mix the ingredients well and apply the resulting paste in a thin layer to the label or adhesive. Leave the mixture on for about 15 minutes. Use anything plastic or a wet cloth to remove. Finally, rinse the glass with soapy water. Toothpaste The principle is that toothpaste contains glycerin, which is a good mixing agent that can dissolve the chemical components of various adhesives. Other cosmetic products also contain glycerin and can also be used to remove the tag. When you mix the paste with baking soda (1:1), you add strength to this method. Apply the toothpaste evenly on the surface of the adhesive, let it sit for a while, and then wipe it off with a soft cloth. Source Apple vinegar Apple cider vinegar is a great pest control tool, but it's also effective at removing glue (even super glue). Adhesive (masking) tape Very effective if the backing of the label is fabric. Tape over the label (press the tape into the label with more pressure) and remove it with a sharp movement. Repeat as many times as needed. Ice Crushed ice is best, but ice cubes will also do. Fill a plastic bag with ice and place it on the sticker. The glue thus cools down, hardens and thus largely loses its adhesive properties. So the sticker should come off without any problem. Chemical removal of labels Notice Be careful with chemical removal. Always test in a hidden place to see if the chosen product does not damage the surface of the product. The least aggressive are technical alcohol and technical gasoline , which will remove most adhesives without etching the substrate (for example, plastic). Acetone or, for example, thinner S6006 for synthetic paint materials is a class stronger agent. Here, however, there is a greater risk of damage to the surface of the product, especially with transparent materials, which may lose their transparency after being etched. The most aggressive of the commonly available solvents is thinner for nitrocellulose coatings – it damages, for example, most plastics. But it is 100% safe when removing labels from glass, porcelain or metal. The strength of the effect (aggressiveness) of the cleaning agent against the impurity (its substrate, health and environment) is determined by the pH level. Acid sensitive surfaces: marble, limestone, sandstone galvanized sheet chrome surfaces cement mixture rubber enamel Base Sensitive Surfaces: aluminium limestone linoleum cotton and silk carpets Isopropyl alcohol Safe for most surfaces. The 70 percent solution breaks down dirt and grease molecules. Apply to the label and let it absorb for 3-5 minutes, then run the label for a while with a cloth soaked in the same cleaner and finally tear it off. Acetone, technical spirit (alcohol) or technical gasoline With this method, it is advisable to ventilate intensively and especially not to smoke! Apply to the label and let it act for 3-5 minutes, then run the label for a while with a cloth soaked in the same cleaner and finally tear it off. Ethanol (alcohol) + ammonia The solution is also effective in removing old brown circles on the table. Mix three parts alcohol, one part ammonia and one part water. Exposure time 1-2 minutes. Nail polish remover If the surface is sensitive to chemicals, use a paint remover that does not contain acetone. Exposure time 5 minutes. Dimexide It is sold at the pharmacy. Exposure time 10 minutes. Notice Some cleaning agents, such as bleach, nail polish remover, or ammonia, interact with metallic materials. In high concentrations, they discolor and damage metals, especially stainless steel. Do not use a scraper or razor on glass with a polymer surface treatment that prevents the penetration of heat and UV radiation. Oxidation and black spots could occur. Removal of labels according to the type of substrate Made of glass Solvents and thinners, oils, Dimexide. From the car window Only products based on alcohol or gasoline or hot air are suitable (effective). Removing a decorative sticker from a car glass is never easy. This is due to the fact that special vinyl-based elements are used for this type of surface. It is a thick and durable composition that is sometimes problematic to remove… Made of fabric and wood Hot air stream. Label adhesive fluid contains resins soluble in water at elevated temperatures. You can use a clothes iron on medium high heat and gently run it over the label. The combination of heat and pressure will weaken the label's adhesion. Be careful not to damage the fabric. From the book Adhesive tape. Stick the tape on the label and gradually tear it off. Made of metal Solvents and thinners, coconut oil and baking soda, mayonnaise, vegetable oils, hot air. Apply the agent to the sponge and rub the sticker well. Remove grease with soap and water. Note Scrape off (rip off, tear off, remove) a label: from glass with a steel scraper or razor blade; from plastic , wood or metal with a plastic spatula or knife, a nail or even an old credit card. Hope you post how to remove labels and adhesive residues at least he helped a little. If you know of any other method, please share with us your experience or your experience :) The source of the images on this page is St Adobe Stock.

Blinds are classic dust collectors, the maintenance of which we postpone (often until the first out-of-place neighbor's remark), even though their cleaning is relatively simple. CONTENT How to clean window blinds Choice of cleaning method and procedure Vertical internal blinds Washing fabric blinds Cleaning fabric blinds "day and night" How to clean fly stains from blackout blinds Horizontal internal blinds Outdoor blinds How to clean window blinds Fold the blinds towards you and wipe vertically from top to bottom. Choose the cleaning solution according to the material the blinds are made of. The best choice is a special agent recommended by the manufacturer. These detergents are not only the most effective, but also have other good properties (for example, they reduce the accumulation of dust). You can use any "non-aggressive" detergent for aluminum blinds and ordinary soapy water for wooden blinds . Clean fabric blinds with a pH-neutral agent. Use a micro cloth to clean. Choice of cleaning method and procedure Dry method If the blinds just need a little dusting, use a standard duster (an old sock will do in a pinch). A home vacuum cleaner will also serve this purpose well. Wet method Pull down the blinds on the window and set the slats of the blinds flat, i.e. in a vertical position. Wipe the slats from top to bottom with a damp cloth. Then flip the slats over and gently wipe from bottom to top (do this carefully to avoid damaging them). Next, set the slats of the blinds in a horizontal position and clean their surface. Wash each slat from both sides and don't forget to clean the upper mechanism of the blinds as well. Vertical internal blinds As a rule, they are made of fabric, and if their manufacturer states that they can be washed, vacuum them first before disassembling and washing them. Washing fabric blinds Wash the fabric blinds by hand using a soft brush in a bath with a pH-neutral detergent (you can also use a milder detergent). Finally, rinse them thoroughly (shower) with lukewarm water and let them dry. Cleaning fabric blinds "day and night" Leave the blinds on the window, do not remove them. First, vacuum the surface with a vacuum cleaner. You can use an ordinary school eraser for smaller stains. Remove larger stains with a mild cleaning agent for textiles (test the agent on a small piece first to see if it discolours the surface). Allow to dry thoroughly. How to clean fly stains from blackout blinds Mix 3 teaspoons of baking soda in the juice of one lemon. Apply this mixture to midges and after ten minutes, remove the stains with a soft brush. Then wipe with a cloth dampened in warm water. If the blinds cannot be washed, at least wipe them with a damp cloth. Warning Never wash fabric blinds in the washing machine or iron them. It is also better to avoid fashionable steam cleaners - hot steam condenses on the slats and thus weakens their structure, causing damage. Info Blinds are also cleaned using ultrasound. Under the influence of high-frequency energy, vacuum and overpressure are created in the water with the cleaning solution, which creates bubbles that subsequently remove dust and dirt. It is not a very widespread method, only about 5 companies operate it in the Czech Republic. Horizontal internal blinds To treat plastic and aluminum blinds, it is best to use an original cleaner, because it removes grease and prevents the accumulation of dust and other impurities. In an emergency, a universal non-aggressive detergent can be used. Notice Be aware of the possible risk of breaking the slats if you press too hard on them during cleaning. Outdoor blinds They should be cleaned at least twice a year, preferably in spring (pollen season) and autumn (increased dustiness). Use a vacuum cleaner before washing. Fold the horizontal blinds to a vertical position and wash with detergent, then flip them over and wash the other side. Finally, you can rinse them with a gentle stream of water, for example from a garden hose. Notice When cleaning, never use products that can bleach or corrode surfaces (wood, textiles). Diluted dish soap or mild soap can be used on non-porous surfaces. When cleaning the blinds, be careful not to break the side guide strings, positioning cords and pull-up straps with a sudden movement. When working, be careful with the cord used to control the blinds (you wouldn't believe how many people have gotten dangerously tangled in it). Avoid buying various "gadgets" designed to clean several slats at once - these inventions (as well as many others) have no right to exist, because they simply do not work as they are supposed to - because they often do the exact opposite of what their manufacturers claim (they do not save time, rather, they lengthen, because it is necessary to wipe the slats with them several times and to clean the area around the guide and functional cords so that the blinds are really clean). Tip Coat the individual slats of wooden blinds or blinds with a candle at least once a month - they will be more flexible and will not break. We believe that these little tips, how to clean window blinds at least they helped a little… The source of the image on this page is St Adobe Stock.

Spatula method, complete instructions - procedure, method, means Are you tired of looking at the world through the dirt on the windows? Do you want really clean windows? And do you want to wash them yourself? If so, take some well-intentioned advice from us. Among other things, this guide will answer your questions: how to wash windows; how to properly wash windows; how to wash windows so that there are no streaks; how to wash windows without chemicals; what to add to window washing water. CONTENT Method Choice of tools and resources Inventory of tools and resources Preparation Procedure and manner How often to wash windows? When to wash windows? The benefit of clean windows Tips and advice at the end Method Generally, there are only two methods of window cleaning: "dry" and "wet" (a malicious pedant may truthfully point out that both are wet, but that's about all he can do). The "dry" way of washing is by using a cleaning solution in a container with a sprayer, when the dirt on the glass is washed away with this solution and a cloth and de facto polishes it . This method is suitable for small glazed areas, partial treatments, not for large ones (unless you are a determined sportsman with a lot of free time). The "wet" procedure, or "squeegee", consists of washing away the dirt with a cleaning solution and then wiping it off . This technique is physically less demanding, roughly the same cost, faster and more effective. And because the classic "wet road" dominates the others, today we present you with instructions for this "squeegee" technique. Choice of tools and resources First: forget about "good old newspapers" and cheap "all-purpose" cleaners that leave streaks on the glass and stains on the frame. In addition, the newspaper gives the windows a static charge, which attracts dust to the glass immediately after cleaning, as well as leaving behind lint and black paint on your hands, which you just use to dirty the frame. The best choice is microfibre cloths , which perfectly absorb moisture. They are more durable and have a far greater effect than any paper products (towels, towels or toilet paper). Inventory of tools and resources A bucket Oval, wide enough to fit a squeegee and a mop. A squeegee Invest in a quality squeegee – it is, after all, the most important window cleaning tool. With its durable rubber blade, a really high-quality squeegee wipes away the solution with dirt in one stroke without faltering. Mop T-shaped plastic tool covered with a sleeve. Profi mops have various improvements, such as the so-called "pad", which is a side strip with an abrasive surface and sharp bristles for easier removal of stubborn dirt. Telescopic rod For mop and trowel to reach higher places. The most frequently used dimension is 1.5 m when retracted and 3 m when extended. But the choice of length is strictly individual - the height of your windows and access to them decide. Scraper To remove stickers, or stubborn dirt, such as old insects, etc. Its size should correspond to the number of such dirt on your windows, as well as the level of your patience. Cleaner The second most important thing. It should be a concentrated alcohol-based agent intended only for washing glass. Alcohol-based preparations dry quickly and at the same time contain other substances that repel dirt and raindrops. Any one-size-fits-all remedy is a bad remedy. Dot. In an emergency, you can use, for example, baby shampoo, but even that has its limits. That is why it is wise to invest in quality when it comes to cleaning products. If you don't want to use chemicals to wash your windows, then you can choose vinegar for washing, for example, which has many great properties... Towels Microfiber, and some plain but clean rags (old towels). The best way to wash windows = how to properly clean windows Preparation The first step is the unpleasant but necessary removal of lower forms of life (spiders, flies, etc.). Get rid of anything smaller than your little fingernail that has lodged itself in the window frame without your knowledge. An ordinary household vacuum cleaner is the best for this, with which you can also get rid of cobwebs and dust in the corners and around the curtains. Disassemble the insect nets and clean them thoroughly in the bathroom or in the garden. If it is the end of autumn, then leave them somewhere stored until spring. Dilute the cleaner according to the manufacturer's instructions, preferably (not necessarily) with distilled water. Hard tap water contains minerals that, after drying, sometimes leave deposits on the glass - streaks and spots that we want to avoid. The water temperature should be a maximum of 20 °C (water that is too warm significantly reduces the effectiveness of cleaning agents), preferably around 15 °C. We recommend adding vinegar to the washing solution , which eliminates grease and removes mineral deposits. It's a great degreaser, playfully breaks down any dead insect remains, removes most mold from window frames and even repels flies. Tip For a basic cleaning solution, we recommend mixing one part distilled vinegar with 10 parts warm water plus detergent. You can also try a one-to-one vinegar to water solution if you don't have any classic cleaning products at home. This sour practice is most widespread in America, where the problem of dirty windows is solved, for example, with a sander: https://www.familyhandyman.com/list/window-cleaning-tips-from-a-pro . Vinegar not only cleans, but also disinfects. Distilled white vinegar, the kind you find in your kitchen, is usually about 5 percent acidic, cleaning vinegar 6. with a pH of 2.0 and acetic acid content, vinegar is an inhospitable environment for many microorganisms. A 2010 study showed that a 10% solution of malt vinegar is a very effective killer of the human influenza A/H1N1 virus. It is also successful in the fight against many types of bacteria, see the mBIO study : https://journals.asm.org/doi/10.1128/mbio.00013-14 . Procedure and manner Start by lightly wiping the dirt from the surface of the window pane with a dry cloth (an old towel will do). This will keep the solution clean for a longer period of time. Continue by washing the frame and both windowsills (interior, exterior), for example using a dish sponge. Check the functionality of the drainage system - whether the drainage holes in the frame are passable (access to them after opening the window on the bottom of the frame, from the outside by turning the cap). Use a vacuum cleaner, cotton swab, wire or cloth to clean them. You can find the full process of checking, maintaining and troubleshooting drains on our blog in the Basic Window Maintenance post. Soak the mop in the washing solution (or apply the detergent to the wet mop directly). First, clean the corners and edges – where the glass meets the frame . Take care, it tends to be the most polluted. Then horizontally, then vertically, and finally with circular movements and even pressure, remove all impurities from the glass. Don't be afraid of foam - foam is your friend (if there's enough of it). The foam makes work easier: dirt is separated from the glass more easily and the squeegee holds its direction better. The bubbles in the solution help keep the water on the glass longer, and it also makes visible water marks that need to be wiped off. The foam also helps reveal dirtier areas that need more scrubbing, as the bubble pattern separates more around grease marks and other dirt. Wipe the frame again with a dry cloth. Yes, he keeps wiping himself and wiping himself, but the point of doing this is meaningful. Really :) If you are unable to remove, for example, dried remains of flies by washing, use a scraper (razor). Notice Hold the scraper firmly at a 45° angle to the glass to avoid snags and scratches. Only drive the blade forwards, never scrape backwards - dirt (cement, etc.) under the blade can cause scratches. If the blade makes a rough or scraping sound when moving, it is dull or broken. Replace it with a new one. Now apply the squeegee – in one continuous motion and with constant pressure at an angle of 45° to the glass . Wipe the water either horizontally, from the left corner to the right, or vertically from the top left corner downwards. Overlap the individual strokes. Professional window cleaners master several wiping techniques, the skills of which require some time to master. The "latest" (created about ten years ago), highly effective method is called "fanning", in which the squeegee is guided by an oblique movement in the direction of an inverted S. And this, when you really master it, is a joy to watch! Judge for yourself, here are two links to a video of this technique (YouTube): Best Window Cleaning Pole Techniques: https://youtu.be/ReVFT0AqWdc . Fanning, Professional Squeegee Method: https://youtu.be/bmc11KqVbEE . At the end of each stroke, wipe the squeegee blade with a micro fiber. (Professionals manage to hold a squeegee under the squeegee when wiping, so that the dirty solution does not get on the windowsill, wall or floor.) Repeat wiping until the water is wiped off the entire surface. Finish the whole process by wiping all the edges of the window with a dry cloth. Use an old towel to wipe the bottom of the frame and its inner profile, microfiber is a shame for such places. Tips We recommend changing the water frequently and keeping the trowel clean throughout the work, either by rinsing it in a bucket of water or wiping it with a damp cloth. This way you will avoid streaks. If a smudge does appear on the glass (it happens when you don't change the water as often as you should), just polish it with a dry micro cloth - it's faster than using a cleaning (polishing) agent, and at the same time just as effective. How often to wash windows? Windows should be cleaned inside and out at least twice a year. For example, in the spring - but only after the pollen season, and in the autumn, as part of the pre-Christmas cleaning. When to wash windows? Stains will be easier to see in sunny weather, but avoid direct sunlight, which will quickly evaporate the solution from the window and leave stubborn streaks. The ideal conditions for washing windows are when the outside temperature is around +10-15 °C. That's when cleaning products work best. Note (for the chilly) It is not necessary to wash windows only under ideal conditions :) The benefit of clean windows elimination of the accumulation of condensate from dead insects, which over time turns into mold in the window frames, which, for example, causes respiratory problems (asthma); more sunlight, which has a beneficial effect on the human organism; reduction of winter energy costs; a 2020 PKO study states that clean windows can increase the average selling price of an apartment by 10%, and a house by up to 14%. Window cleaning is therefore also an affordable way to increase the value of your investment - a way to increase interest in buying or renting; extending their lifespan. The more often you wash your windows, the easier and faster each wash will be. Tips and advice at the end Use glycerine against dust Add a little glycerin to the cleaning solution - it significantly reduces the accumulation of dust and stains after rain. Anti-icing of windows In the winter season, add a small amount of alcohol or ammonia to the solution - they are very effective in preventing the glasses from freezing. Making frosted (blind) glass transparent Apply linseed oil to the glass (perhaps with an old towel) and wipe it off with a paper towel after an hour. Then wash the glass in your usual way. If you only need to clean a small part of the window, use the classic "dry" cleaning method. A cleaning product and a micro cloth will suffice for this. Here is a guide to one of the best (most effective) cleaning solutions: Mix 250 ml of vinegar, 200 ml of alcohol, a spoonful of starch and 200 ml of water. Pour the mixture into the sprayer and use a microfiber cloth to wash the window in the usual way. That's all. We are convinced that the trowel method is the most effective of all - both in terms of cleanliness and shine. In addition: windows washed in the manner described above do not need to be polished! Post content how best to wash windows is the result of our many years of experience in this field, which we are happy to pass on. Quotations from our blog posts are often published on specialized sites, for example: https://themagazineworld.com/how-to-easily-tackle-tough-grease-and-grime-on-your-oven-and-hob-glass/ . We believe we have helped. The rest is up to you... Images on this page are sourced from Depositphotos.

instructions on how to adjust plastic windows so that they do not rub and heat does not escape This post will answer these questions for you:   What types of windows do we have? Why is it important to adjust plastic windows? How do I know that the windows need to be adjusted? What tools and materials are needed to adjust the windows? How to adjust plastic windows step by step? Axis settings Height adjustment Diagonal settings Adjustment of contact pressure How often should I check and adjust my windows? This procedure will help you ensure that your windows will perform optimally and contribute to energy savings. Basic types of windows: Rotating window: the sash is attached to the left or right side of the frame. Hinged window: the window is fixed at the bottom of the frame. Hinged window: the window is fixed in the upper part of the frame. Pivot window: the window sash rotates around its axis, which is located in the middle. Sliding window: one part of the window can be extended upwards, the other is permanently glazed. Why is it important to adjust plastic windows? Proper adjustment of plastic windows is key to maintaining good insulation and preventing heat loss. When the window sash, usually due to temperature fluctuations, begins to rub against the frame, it is necessary to adjust it - leaks that lead to heat loss, higher energy bills and discomfort in the home. Window adjustment should be done by an expert, but if you are a seasoned handyman, or at least a somewhat manually skilled individual, you can adjust the windows yourself. How to recognize that the windows need to be adjusted? If the window rubs when opening or closing, there are gaps between the frame and the sash, or if you feel a draft, it's time for an adjustment. Another signal is when the windows do not close straight and tightly. What tools and materials are needed to adjust windows? You will need a Phillips screwdriver and possibly an Allen key for basic adjustment. A step stool or ladder may also be useful if you are working with higher windows. Plastic windows (depending on the brand and type) are adjusted by screws in the upper and lower hinges with a hexagonal Allen key (mostly 4 mm in size), both in height and laterally in relation to the frame. After removing the hinge covers, tighten or loosen the upper and lower fittings as needed. We also adjust the pressure of the window sash with the upper scissor hinge, in the open position. We adjust the height setting on the lower hinge when the wing is closed. How to adjust plastic windows so that they do not rub and heat does not escape. How to adjust plastic windows step by step? Open the window: open the window fully to access the screws that need to be loosened. Loosen the screws: there are several screws (usually four) on the window frame that hold the window sash in the desired position. Loosen these screws slightly. Height and position adjustment: if the window rubs when closing or if the seal is uneven, you can carefully move the window up or down until you achieve the correct alignment. Re-tighten the screws: after adjusting the position of the window, re-tighten the screws firmly to keep the window in place. Leakage check: after adjustment, open and close the window several times to make sure it moves easily and seals properly. Most windows have a tilt and turn mechanism: corner bearing – on the stop side in the lower corner of the window scissor bearing - located in the upper corner locking and mushroom pins - usually on the handle (security windows) Axis settings Adjust the window sash that gets stuck to the side with a corner and scissor bearing. During the adjustment, alternately turn the set screws until the window sits straight. Turning the corner bearing counterclockwise and the scissor bearing clockwise causes the sash to move in the direction of the hinge. When the direction of rotation is reversed, the sash moves towards the window handle. Height adjustment It is performed on the lower corner bearing. Turn the screw clockwise to raise the window. Turning the screw counter-clockwise lowers the window. Diagonal settings If the sash hangs crooked, adjust it using the adjusting screw in the scissor bearing. By turning the screw clockwise, the window sash is lifted up. When turning counter-clockwise, the wing descends. Adjustment of contact pressure If the window cannot be closed, the pressure must be adjusted. This is done by the locking pins of the window sash, which we turn clockwise or counter-clockwise. This increases or decreases the contact pressure. How often should windows be checked and adjusted? It is recommended to check and possibly adjust the windows once a year, ideally before winter, when it is necessary to ensure maximum insulation. This procedure will help you keep the windows in perfect condition, minimize heat leaks and ensure long-term functionality. Recommendation Do not adjust hanging window sashes in winter or summer - at high temperatures, the expansion of the profile increases and at low temperatures, on the contrary, it shrinks, so the adjustment cannot be accurate. The ideal time for adjusting windows is therefore spring and autumn. Remember that well-adjusted windows save your health and your wallet! Mold and foggy windows are mostly the result of improper ventilation , which people try to solve with micro ventilation, which is wrong. It is ideal to ventilate several times a day with fully open windows for about 5 minutes. A secondary, no less significant effect of such ventilation is a noticeable change in the atmosphere, which awakens from lethargy, contributes to concentration - and generally improves the mood... Images on this page are sourced from Depositphotos.

Some well-intentioned tips on the subject Cleaning of glass surfaces Window glass Keeping windows and other glass surfaces sparkling clean can be a daunting task, but with the right tips and tricks, it doesn't have to be a daunting task. Here are some effective and environmentally friendly cleaning solutions using common household ingredients that will leave your glass surfaces sparkling. For a streak-free surface , mix 250 ml of water with five tablespoons of cornstarch in a spray bottle. Shake well, spray on surface and wipe. For extremely dirty windows , try a mixture of 2 cups water, ¼ cup white vinegar, and ½ cup dish soap. Frosted glass To clean cloudy glass surfaces , also known as "blind glass," rub linseed oil on them and let sit for an hour. Then clean with regular glass cleaner. Cut glass Mix ½ package of baking powder, juice of half a lemon and two tablespoons of salt. Apply the mixture to the window with a microfiber cloth and polish the surface with circular movements. Crystal glass (chandeliers) Mix a liter of warm water with a tablespoon of ammonia. You can also use this solution on metal parts. Wipe and polish the surface with a microfiber cloth. Fireplace glass For fireplace glass soiled with soot, mix fine ash with baking powder and use newspaper to scrub the glass in a circular motion. This simple solution will help remove even the most stubborn stains. For really stubborn stains , mix 250ml of water with a teaspoon of benzine and a few drops of glass cleaner. We hope these glass cleaning tips have been helpful in removing dirt and grime from your windows and other glass fixtures. With these simple yet effective cleaning solutions, you can keep your glass surfaces spotless and crystal clear. Remember that a little effort will help to maintain a clean and pleasant home environment...

A quick guide How to remove permanent marker from different surfaces usually by a non-toxic method. Made of wood Alcohol (regular unflavored vodka) Ethyl alcohol Lysopropyl alcohol Toothpaste (white, not gel) with sodium bicarbonate (1:1) Hairspray (not for varnished wood!) Disinfectant Nail polish remover Sunscreen Pencil eraser Made of glass WD-40 Regular toothpaste mixed with baking soda Nail polish remover Alcohol White vinegar, warm water (1:1) One part bleach, warm water (1:3) Made of metal (stainless steel kitchen appliances, moldings, fittings, etc.) Liquor WD-40 Chalk, caustic soda, oat flour, warm water (1:1) Toothpaste (white, not gel) Dry erase marker From the tiles Toothpaste (white, not gel) Hair spray Pencil eraser From granite Alcohol Isopropyl alcohol Chalk, caustic soda, oat flour, warm water (1:1) Made of plastic Acetone Alcohol WD-40 Toothpaste (white, not gel) , baking soda (1:1) Peanut butter From laminate Vegetable oil WD-40 From the wall Aerosol hairspray Alcohol Hand sanitizer Pencil eraser From clothes Alcohol (Vodka, Slivovice) Technical alcohol Alps Nail polish remover Hair spray Wash the clothes immediately afterwards! Notice Before applying oil products, always test them on an inconspicuous area to verify any reaction with the surface. If you know of another method how to remove permanent marker share your experience with us...

or The degree of difficulty of cleaning the window is determined by its type (more precisely, the way it is opened) Not all windows can be opened so that you can wash them. And if it is not possible to clean them from the outside, they must be dismantled. That's why here's a tutorial: How to prepare windows for washing Opening and closing of window sashes can take place in different modes: tilt , swing , tilt . These manipulations with the window are possible thanks to the so-called fittings . Fittings are classified according to the method of opening the sash and direction, as well as according to its weight. It is an internal mechanical system that is fitted in the grooves of the frame and wing. We control this system with a window handle, which can usually be turned 180 degrees on a tilt and turn window. The 90 degree position is the opening position and the 180 degree position is the opening position for the sash. Many windows can be opened like a book (horizontally and vertically), giving full access to the exterior glass. The least problematic are pivoting (opening inwards or outwards depending on the location of the outer face), swinging and tilting (facing inward) windows. However, there are also those that do not provide complete access, as their manipulation possibilities are limited by a special purpose, specific function or construction subject to, for example, exclusively design. As a rule, these are tilting (outward), tilting (roof), sliding (usually roof) and, of course, fixed windows... The most common way to make the window accessible for washing As a rule, for all types, by closing to an angle of 15° and: by pulling the scissor hinge up or down from the window; by manually releasing the latch on the scissor arm, which causes the window to swing into the cleaning position. Access to the outside of all double-hung windows (except fixed) allows the lock to be unlocked at the top, bottom or side of the frame. Usually by moving the latch (tilt lock, opening limiter, sash rotation lock) to the opposite side. But most of them only provide a small open space, which makes cleaning difficult. Additionally, not all double-hung windows fold inward. Location of safety locks on scissors: Window scissors are known by many names (scissor handlebars, scissor cuffs, axle arm or handlebar tape). It is important to distinguish between functional, catching and cleaning scissors. Functional scissors are described above. Catching and cleaning shears are window shears that are additionally mounted on large window sashes as a safety device. However, it only engages when the functional scissor fails or the sash is removed from the functional scissor for cleaning purposes. Hopefully this guide on how to prepare windows for washing has helped you at least a little. Some of our customers have admitted to relying on specialized tools such as a U-shaped cleaning rod with a washer and squeegee on both ends to clean the outside of their windows. When they found out how clumsy (and time consuming) these rods were, they decided to hire professionals instead. With enough experience, quality tools and cleaning products, most people can effectively clean the inside of windows - but the outside is a completely different story... The source of the images on this page is St Adobe Stock.

Ordinary homemade vinegar is a magical thing even far beyond the boundaries of the kitchen. People are constantly discovering its capabilities and thus new uses. Vinegar repels dandruff or insects, eradicates mold, polishes windows, removes paint drops from glass or a label from your beloved chest of drawers. But it cannot be used always and for everything - it is not omnipotent! Sometimes its use is completely unnecessary, sometimes it can be harmful, and sometimes it is downright dangerous. There is 7 examples of when not to use vinegar Vinegar is not soap . It is not an alkaline cleaner that can easily handle dishes and pots. Vinegar has no effect on grease; Do not use vinegar to clean marble kitchen countertops! May cause pitting and corrosion (Marble Institute); Do not use vinegar to clean plastic surfaces! Some species can be colored or discolored; Do not use it to clean your smartphone or laptop monitor! The displays (screens) have a thin layer of oleophobic coating that reduces fingerprints and smudges. Acidic vinegar can remove it; Cast iron and aluminum are reactive surfaces! If you want to use vinegar to clean pots and pans, use it exclusively on stainless steel and enameled cast iron cookware, it corrodes other metals; Never add vinegar to bleach! This mixing produces chlorine gas, the substance used to kill soldiers in the First World War (!); Do not use vinegar as an insecticide. The pest also kills with the plant. Keep these 7 examples of when not to use vinegar in mind and life will be beautiful…